EK Water Blocks
**B Grade** EK-FC980 GTX - Acetal+Nickel
- EK-FC980 GTX is a high performance full-cover water block for nVidia reference (NVA-1G401) design GeForce GTX 980 series graphics cards.
Stock Code: BG-100-EK
EAN: 00000000
MPN: BG-100-EK
Manufacturer: EK Water Blocks
Supported by the biggest tech community forums.overclockers.co.ukDirect Service Hotline
+44 (0)1782 44 44 55
+44 (0)1782 44 44 55
Product information:
This water block directly cools the GPU, RAM as well as VRM (voltage regulation module) as water flows directly over these critical areas thus allowing the graphics card and it's VRM to remain stable under high overclocks. EK-FC980 GTX water block features a central inlet split-flow cooling engine design for best possible cooling performance, which also works flawlessly with reversed water flow without adversely affecting the cooling performance. Moreover, such design offers great hydraulic perfromance allowing this product to be used in liquid cooling systems using weaker water pumps.
Base is made of nickel plated electrolytic copper while the top is made of quality POM Acetal material. The sealing is ensured by quality rubber washers. Screw-in brass standoffs are pre-installed and allow for safe, painless installation procedure. Block is mounted with enclosed M2.5 DIN7985 screws and allows for re-use of the original NVIDIA backplate.
EKWB recommends the purchase of aesthetic retention backplate (EK-FC980 GTX Backplate - Black or Nickel) which improves the looks of your graphics cards and also provide some passive cooling to the circuit board VRM section.
G1/4" threaded fittings can be used on both sides of the FC terminal. Up to four EK-FC980 GTX water blocks can be used on a single ATX form factor motherboard by using EK-FC Terminal (DUAL, TRIPLE or QUAD type) system or other means of interconnectivity. Please note that EK-FC Bridge & Link system is not compatible with this water block.
EK-FC980 GTX series product is also the choice of EVGA for their factory liquid cooled NVIDIA GeForce GTX 980 HydroCopper series graphics cards.
Enclosed:
- EK-FC980 GTX series water block
- mounting mechanism with screw-in brass standoffs
- thermal pads
- thermal grease EK-TIM Ectotherm (1g)
Made in Slovenia - Europe!
PLEASE NOTE:
- Due to immense variety of fittings/barbs available on market and no prescribed standards, we guarantee compatibility only for connectors bought from our web site.
- Water block ports' aligns with the EK-FC780 GTX Ti, EK-FC770 GTX (GW), EK-FC780 GTX Jetstream, EK-FC Titan as well as EK-FC Titan SE
**B Grade** EK-FC980 GTX - Acetal+Nickel
Below is the original description for this product, any reference to warranty is to be ignored. Warranty for this item is 90 days as with all B Grade items.
B Grade items may have been used, have damaged packaging, missing accessories or a combination of these (Motherboards may be missing I/O shields).
Some items may have scuff marks or slight scratches but should otherwise be an operable product.
EK-FC980 GTX is a high performance full-cover water block for nVidia reference (NVA-1G401) design GeForce GTX 980 series graphics cards. Please check our Cooling Configurator online compatibility system for detailed compatibility list!B Grade items may have been used, have damaged packaging, missing accessories or a combination of these (Motherboards may be missing I/O shields).
Some items may have scuff marks or slight scratches but should otherwise be an operable product.
This water block directly cools the GPU, RAM as well as VRM (voltage regulation module) as water flows directly over these critical areas thus allowing the graphics card and it's VRM to remain stable under high overclocks. EK-FC980 GTX water block features a central inlet split-flow cooling engine design for best possible cooling performance, which also works flawlessly with reversed water flow without adversely affecting the cooling performance. Moreover, such design offers great hydraulic perfromance allowing this product to be used in liquid cooling systems using weaker water pumps.
Base is made of nickel plated electrolytic copper while the top is made of quality POM Acetal material. The sealing is ensured by quality rubber washers. Screw-in brass standoffs are pre-installed and allow for safe, painless installation procedure. Block is mounted with enclosed M2.5 DIN7985 screws and allows for re-use of the original NVIDIA backplate.
EKWB recommends the purchase of aesthetic retention backplate (EK-FC980 GTX Backplate - Black or Nickel) which improves the looks of your graphics cards and also provide some passive cooling to the circuit board VRM section.
G1/4" threaded fittings can be used on both sides of the FC terminal. Up to four EK-FC980 GTX water blocks can be used on a single ATX form factor motherboard by using EK-FC Terminal (DUAL, TRIPLE or QUAD type) system or other means of interconnectivity. Please note that EK-FC Bridge & Link system is not compatible with this water block.
EK-FC980 GTX series product is also the choice of EVGA for their factory liquid cooled NVIDIA GeForce GTX 980 HydroCopper series graphics cards.
Enclosed:
- EK-FC980 GTX series water block
- mounting mechanism with screw-in brass standoffs
- thermal pads
- thermal grease EK-TIM Ectotherm (1g)
Made in Slovenia - Europe!
PLEASE NOTE:
- Due to immense variety of fittings/barbs available on market and no prescribed standards, we guarantee compatibility only for connectors bought from our web site.
- Water block ports' aligns with the EK-FC780 GTX Ti, EK-FC770 GTX (GW), EK-FC780 GTX Jetstream, EK-FC Titan as well as EK-FC Titan SE
More links for "**B Grade** EK-FC980 GTX - Acetal+Nickel"
Recently Viewed
Customer review
No Review Yet
This is your chance!
Be the first to review this product
Write a review