Bitspower
Z-Multi Ultra 250mm Reservoir (POM Version)
- 250 mm Reservoirs of Bitspower
- 5x G1 / 4-inch threaded
- Transparent acrylic tube
- POM cover with Aqua-Pipe
- POM floor with Vortex-Killer
- incl. fastening materials
Stock Code: WC-662-BP
EAN: 4719552225408
MPN: BP-WTZMU250P-CLBK
Manufacturer: Bitspower
Supported by the biggest tech community forums.overclockers.co.uk
+44 (0)1782 44 44 55
Product information:
In addition to these purely practical aspects Reservoirs also have visual Highlights. Acrylic Tubes have been specially suitable because of their transparent optics and various modding possibilities (lighting, colored liquids, etc.).
This model of the Reservoir comes with two screwed-POM-lids. The lids are sealed with two rubber rings against the acrylic tube. The top lid ihas a G1 / 4-inch thread with an Aqua-Pipe on the inside, which achieves a visual extension from the outside.
The lower POM cover on the other hand has four G1 / 4-inch -Thread. One of these openings is connected to an internal flow tube. This is used as a feed when the inlet and outlet are both out of the bottom of the reservoir. If the feed from the top, however, one of the other openings should be used as the end, as at a water level below the height of the flow tube will cause air to be sucked in to the loop.
The package includes three sealing plug, with which the respective unused openings can be sealed. Further, two mounting rings are included which are simply pushed over the tube and compressed at the desired location.
Specifications:
- Dimensions: 302 x 60 mm (length x diameter)
- Material: Acrylic (tube), POM (cover / bottom)
- Thread: 5x G1 / 4 inches
Contents:
- 1x Reservoir
- 1x Conditions mounting kit
- 1x Aqua-Pipe G1 / 4-inch
- 1x Z-Cap cover
- 3x plug (silver-plated)
Z-Multi Ultra 250mm Reservoir (POM Version)
eservoirs provide the water cooling a storage depot, to compensate for the natural reduction of the cooling liquid, for example in the form of diffusion through the tubing and to prevent air bubbles in the circuit, which in turn could lead to increased operating noise of the pump.In addition to these purely practical aspects Reservoirs also have visual Highlights. Acrylic Tubes have been specially suitable because of their transparent optics and various modding possibilities (lighting, colored liquids, etc.).
This model of the Reservoir comes with two screwed-POM-lids. The lids are sealed with two rubber rings against the acrylic tube. The top lid ihas a G1 / 4-inch thread with an Aqua-Pipe on the inside, which achieves a visual extension from the outside.
The lower POM cover on the other hand has four G1 / 4-inch -Thread. One of these openings is connected to an internal flow tube. This is used as a feed when the inlet and outlet are both out of the bottom of the reservoir. If the feed from the top, however, one of the other openings should be used as the end, as at a water level below the height of the flow tube will cause air to be sucked in to the loop.
The package includes three sealing plug, with which the respective unused openings can be sealed. Further, two mounting rings are included which are simply pushed over the tube and compressed at the desired location.
Specifications:
- Dimensions: 302 x 60 mm (length x diameter)
- Material: Acrylic (tube), POM (cover / bottom)
- Thread: 5x G1 / 4 inches
Contents:
- 1x Reservoir
- 1x Conditions mounting kit
- 1x Aqua-Pipe G1 / 4-inch
- 1x Z-Cap cover
- 3x plug (silver-plated)
More links for "Z-Multi Ultra 250mm Reservoir (POM Version)"
Recently Viewed
Customer review
No Review Yet
This is your chance!
Be the first to review this product
Write a review