Cisco Switches

Soldato
Joined
8 Jun 2005
Posts
3,698
Location
London
burnsy2023 said:
I'm after a 24 port 100mbps Cisco switch with gigabit fibre uplinks. Basically a Cisco 2950 with an uplink.

What models can you suggest?

Burnsy

2950 24 port should do it, they come with 2 GBIC interfaces which allows you to connect fibre GBIC converters, They cost around £800

Quite a few for sale on "The auction site"
 
Man of Honour
OP
Joined
17 Nov 2003
Posts
36,743
Location
Southampton, UK
I've finally found a number for Cisco and phoned them up (thats not easy to find). I need 15 2950-24 and 5 2950SX-24. Unfortunetly this is for work and we need the gaurentee etc, but I've had a quote for about 8.5K.

Burnsy
 
Soldato
Joined
18 Oct 2002
Posts
7,139
Location
Ironing
didn't think the 2950 had gigabit uplinks - mine at home doesn't. The 3500 under my desk is a 48-port but does have dual gigabit fibre uplinks....
 
Soldato
Joined
7 May 2003
Posts
4,247
Location
Away from here
growse said:
didn't think the 2950 had gigabit uplinks - mine at home doesn't. The 3500 under my desk is a 48-port but does have dual gigabit fibre uplinks....

You're right - it doesn't have gig uplink ports.

You need to look at the 2950-24EL if you want GBIC's or 2950-24T if you want RJ45 uplinks.
 
Soldato
Joined
8 Jun 2005
Posts
3,698
Location
London
lol oh well,

we've got nearly 300 2950s at work and they've all got Gbics, I dunno the actual model number but I don't order them. 2924G I belive is the one you want.
 
Associate
Joined
20 Aug 2003
Posts
2,139
Location
The Republic
Part number/description:

WS-C2950G-24-EI = 24 10/100 ports + two 1000BASE-X ports
WS-C2950T-24 = 24 10/100 ports + two 1000BASE-T ports
WS-C2950C-24 = 24 10/100 ports + two 100BASE-FX ports

If the uplinks are just between cabinets then the WS-C2950T-24 is the one you are after - however the top option gives you the flexibility of using GBICs if required.

GBIC part numbers are:
WS-G5483= 1000-Base T GBIC
WS-G5486= 1000-Base LX GBIC (long-haul, singlemode)
WS-G5484= 1000-Base SX GBIC (short-haul, Multimode)
 
Man of Honour
OP
Joined
17 Nov 2003
Posts
36,743
Location
Southampton, UK
Right, I need one more switch. This needs to have at least 16 gigabit copper ports but at least 24 would be preferable. It also needs minimum 6 fibre ports but 8 would be preberable.

We currently have SC type fibre patch cables, but the 2950SX has MTRJ fibre connectors, so i'm not sure if they do SC ports outside of a GBIC. And it needs to be short haul, multimode.

Any ideas on a model?

Thanks

Burnsy
 
Soldato
Joined
8 Jun 2005
Posts
3,698
Location
London
burnsy2023 said:
Right, I need one more switch. This needs to have at least 16 gigabit copper ports but at least 24 would be preferable. It also needs minimum 6 fibre ports but 8 would be preberable.

We currently have SC type fibre patch cables, but the 2950SX has MTRJ fibre connectors, so i'm not sure if they do SC ports outside of a GBIC. And it needs to be short haul, multimode.

Any ideas on a model?

Thanks

Burnsy

Don;t think you can fit all the above into a single Cisco model, with 16 gigabit copper ports and 8 ports cable of SC fibre, Gbic or not, there isn't a model which does all of that.
For a switch which does 16 port gigabit copper, the new 2960s are pretty good, WS-C2960G-24TC-L is the cheapest gigabit switch they do.
For 8 fibre connections you'd need something like a 3550-12G which would give you 10 Gbic interfaces and 2 copper interfaces, again expensive.

If it was me, i'd get the 2960 with 24 gigabit ports, then buy 8 fibre line drivers, like a Lancast box or something. plug those into 8 ports on the 2960 to convert them to fibre, and your away.
 
Associate
Joined
20 Aug 2003
Posts
2,139
Location
The Republic
As V-spec says, ther is nothing in the Cisco range that will cover that lot (unless you fancy a 6500 :D ) - the 3560-24G is probably the closest with 24 copper and 4 SFF (small form factor) GBIC slots. The 3550-12G that V-Spec mentioned is about to be EOL as well (think it's the end of March) so if you go down that route be quick.
 
Man of Honour
OP
Joined
17 Nov 2003
Posts
36,743
Location
Southampton, UK
Ok, What if I were to split it and have a stanard Gigabit copper switch (easy enough to find) and a dedicated Fibre switch. For the fibre switch I'd need at least 8 ports with MT-RJ connectors. Any switch that could do this without GBICs, as they're extra cost? I'm finding it hard to get a switch without a rediculous number of ports left over and a pricetag that would make babies cry.

Question about the SFF GBIC slots, do they have two ports per module as standard large GBICs(in MTRJ format)?

Burnsy

Edit: I've got someone from Cisco presales support calling monday so hopefully that'll clarify everything if I'm not crystal clear by then.
 
Soldato
Joined
8 Jun 2005
Posts
3,698
Location
London
burnsy2023 said:
Ok, What if I were to split it and have a stanard Gigabit copper switch (easy enough to find) and a dedicated Fibre switch. For the fibre switch I'd need at least 8 ports with MT-RJ connectors. Any switch that could do this without GBICs, as they're extra cost? I'm finding it hard to get a switch without a rediculous number of ports left over and a pricetag that would make babies cry.

Question about the SFF GBIC slots, do they have two ports per module as standard large GBICs(in MTRJ format)?

Burnsy

Edit: I've got someone from Cisco presales support calling monday so hopefully that'll clarify everything if I'm not crystal clear by then.


3560s are very expensive, also, the SFP connections on a 3560 mean you need different patch cables then normal SC for a Gbic, because the connections are tiny.
If It was me, and I was trying to save money i'd buy a 2960 and get a load of fibre transceivers for the fibre.
 
Back
Top Bottom