Search results

  1. Skittle

    KFA RTX 3080 TI HOF fan speed control

    Hi Mwalsham, I have the exact same card and I'm seeing the exact same thing in MSI Afterburner and GPU-Z. I think there are two types of fans, 2 x 100mm fans which I think are driven off the same header so they appear as one, the middle fan is a 92mm fan so it's probably driven off a different...
  2. Skittle

    KFA2 GeForce RTX 3080 Ti HOF - Coil Whine

    I can confirm that KFA2 3080Ti HOF does work with MSI Afterburner. Have you enabled all the compatibility options in MSI Afterburner?
  3. Skittle

    *** NVIDIA GEFORCE RTX 3080 SERIES STOCK SITUATION - NO COMPETITOR DISCUSSION ***

    Guys, I'm position 1838 in the queue for an Asus Tuf card, just by the rate at which that particular queue is going down I figure 1st March might see me getting this damn card. Anyone recently order a GeForce RTX 3080 Eagle OC that's at a more reasonable queue length?
  4. Skittle

    Gigabyte Z170X-Gaming 7 Owners Thread.

    Dud Chip for Overclocking? Hi All. I have this board with an i7 6700K chip, RAM is Corsair Vengeance LPX 16GB (2x8GB) DDR4 PC4-24000C15 3000MHz. Cooling is a Noctua DH-15s air cooler. I've tried overclocking this to 4.6GHz but I've had no joy. I managed to get 4.5GHz to be stable but I'm...
  5. Skittle

    Corsair HX 850W ATX Modular PSU has died

    I had the exact same problem with mine two weeks ago. You have to send the PSU back to Holland, which aint cheap considering the PSU weighs 4.5Kg. Also make sure that however you send it, you get a registered delivery (i.e. signature required on delivery), as they managed to lose mine after UPS...
  6. Skittle

    A Question for Dell U2410 owners

    They only light up when your hand comes near them, otherwise they are off. You have to touch the actual lights as there are no push buttons. The only light which is permanently on is the power light.
  7. Skittle

    Strange problem with Akasa Vipers in Push/Pull configuration

    Ok I seem to have fixed the problem. I plugged the fan directly into the motherboard CPU fan header and it worked fine. I then reconnected back in the splitter cable and connected the fans the way they were supposed to be connected and both fans worked as expected. I think some of the problem...
  8. Skittle

    Strange problem with Akasa Vipers in Push/Pull configuration

    I've switched the fans around and the problem switched fans too so it's not the fan, it's whatever fan is plugged into the CPU Fan part of the PWM splitter cable just goes to 100% all the time. So I've put both fans into the two Case Fan part of the splitter cable and both are running slow as...
  9. Skittle

    Strange problem with Akasa Vipers in Push/Pull configuration

    Yep I've checked them again. There's 2 Case Fan connectors (3 wires), 1 CPU Fan connector (4 wires) and a 4 pin molex power connector.
  10. Skittle

    Strange problem with Akasa Vipers in Push/Pull configuration

    I have two Akasa Viper PWM fans that I'm trying to set-up in a push/pull CPU cooler config. My motherboard is a Gigabyte GA-X58A-UD7 (Rev. 1.0). I have gotten the Akasa AK-CB002 PWM Fan Splitter Cable splitter cable and I've plugged the motherboard connector into the mobo CPU fan header. One of...
  11. Skittle

    C300 on SATA3 TRIM issues

    So how do you switch to the MS drivers if the C300 is your boot drive. I read somewhere that it's as simple as going in and going to device manager, click on the controller and say Update driver and then just pick the "Standard AHCI 1.0 Seial-ATA-Controller" instead of the "Marvell 91xx SATA 6G...
  12. Skittle

    what temps can i expect to get with this bundle?

    @scubes: If I remember correctly, core 2 was 1-2 degrees cooler, cores 3 & 4 were around 84-86C. I didn't let the stress test go on for much longer than 10-15 minutes as I thought I was going to melt something. But I noticed that as time went on, the temperature in the other cores was rising up...
  13. Skittle

    what temps can i expect to get with this bundle?

    I have that bundle in an Antec 902 case. I did a Prime95 stress test and the temps were around 90~92C on the first core.
  14. Skittle

    i7 930 temp check.

    I have the Overclockers.co.uk i7 930 oc'd to 4.2GHz bundle. It is stable and ran at 4.2GHZ, however the temps were horrible! Doing a Prime95 or LinX test, the temperatures would hit 90C! I have a Megahalem + Sharkoon CPU fan and a Antec 902 case with all fans running and I've reseated the...
  15. Skittle

    i7 930 temp check.

    My temps are pretty close to yours, under load I hit 56C.
  16. Skittle

    What would be a normal temp for an i7 930?

    I've an i7 930 overclocked to 4.2GHz. When I run a Prime95 or Linx stress test, Core 0 shoots up to 88~90C, other cores are 1-4 degrees behind that. I'm using a Megahalem and one fan in an Antec 902 case. Are those temp too high even for a 4.2GHz overclock? VCore is 1.325. Oh I have reseated the...
  17. Skittle

    AS SSD Benchmark benchmarks!

    C300 128GB SATA III
  18. Skittle

    Gaming Keyboard and/or GameBoard

    At the risk of being lynched by other members here, I use a MS Natural keyboard for gaming. It takes a while to get used to but the curvature helps your wrists, also they tend to have bug CTRL, ALT and Space Bar keys. Anyone else using ergonomic keyboards for gaming?
  19. Skittle

    Overclocked Bundle

    I was wondering about those bundles too. If I order a bundle and order more memory e.g. from 4GB->8GB or 6Gb->12GB will you test the overclock with the extra memory added? I've heard that it's harder to overclock some systems when you have both memory banks full?
  20. Skittle

    Motherboard won't let me overclock...

    Hi all, Firstly, my kit: Gigabyte GA_P35_DQ6 (Socket 775) PCI-Express DDR2 Motherboard Intel Core 2 Duo E6850 "LGA775 Conroe" 3.00GHz (1333FSB) Crucial Ballistix (4x1GB) DDR2 PC2-8500C5 1066MHz Dual Channel Kit At the weekend I tried to overclock my machine by setting the FSB to...
Back
Top Bottom